 |
| Quantity: | |
|---|---|
Feature Of Mechanical Fliter
●JTGMF Mechanical (Carbon,Sand)Filter Housing is an important part for Pure water preparation early pre-Finish and water purification system.It is apply to drinking water standard industrial water which is required filtered and general turbidity of treated water is within 5mg/L. It has good remove effect for suspended solids in industrial sewage.The Tablet agglomerated from suspended solids in water which can not remove through Precipitation method,we can through water to filter layer in filter vessel.Finally,to achieve transparency in water.
●JTGMF Mechanical Filter Housing using multichannel polishing processing to ensure the interface Ra reach to 0.6um close to sanitary level.All of the surface is mirror polished.
Application
●It is used in water Finish,mainly used in turbidity removal,reverse osmosis and The front-end preprocessing of lon exchange softening desalination system.It also can be used in remove sediment in Surface water and groundwater.The requirement of influent water turbidity should less than 20degrees,and the turbidity of treated water can below 3 degrees.
●Can be widely used in Electronic power,oil chemical industry,metallurgy,electroplating,paper making,textile,pharmaceutical dialysis,food and beverage,drinking water,Factories in water,swimming pool,etc.To meet the needs of the various industries liquid filtration.
The Characterstic Of Mechanical Fliter
●Barrels internal and external surface using mirror polish,interface Ra reach to 0.4um close to sanitary level.
●The equipment low cost,low Operating cost and easy management.
●Reasonable structure design,after Filter material backwashing can use many times,filter material has long service life,effective filtering and small occupation area.
Surface Finish
Finish Type | Mechanical polishing, electrolyticpolishing, sand blasting, pickling |
Polishing Precision | Inner surface Ra≤0.4μm , |
Operating Conditions
Max Operating Pressure | 0.4MPa, 0.6MPa |
Max Operating Temp. | 120℃ |
The filter shell adopts：ATM(pressure testwith full water) | |
Material
Filter shell | SS304, SS316L |
Stabilizer Blade, sling | SS304 |
Connect Pipe | SS304 |
O-ring | EPDM, PTFE, Viton, Silicone |
Connection
In-outlet N1, N2 | 1”/2”Flange, Tri-clamp,Thread |
Pressure gauge connectionN3, N4 | 1.5”Screw thread |
Vent valve connection N5 | 1/4”Screw thread |
Sight glass connection N6 | Flange |
Manhole N7 | Flange |
Packing Hand hole N8 | Flange |
Dimension Parameters | C： Shell diameter | ||||||||||
Φ600 | Φ800 | Φ1000 | Φ1200 | Φ1400 | Φ1600 | Φ1800 | Φ2000 | Φ2500 | Φ3000 | Φ3200 | |
A： Total height | 2350 | 2600 | 2800 | 2800 | 3000 | ||||||
B： The distance from inlet to center | 1500 | 1800 | 1800 | 2000 | |||||||
D： The height from packing hand hole to ground | 1200 | 1200 | 1200 | 1200 | |||||||
E: Equipment output(T/h) | 1.4～2.8 | 2.5～5.0 | 4.0～8.0 | 5.5～11 | 7.5.4～15 | 10～20 | 13～25 | 16～30 | 25～49 | 35～70 | 40～80 |
The above-mentioned data is the standard, it can customize according tocustomer's requirements.
Selection Table
Shell diameter | Shell material | In-outlet connection | O-ring | |||
600J | 4 | K | S | |||
600J=diameterΦ600 mechanical filtration | 4=304 | F=Flange | E=EPDM | |||
800J | 1000J | 1200J | 1400J | 6=316L | K=Tri-clamp | P=PTFE |
1600J | 1800J | 2000J | 2500J | L=Screwthread | V=Viton | |
3000J | 3200J | S=Silicone | ||||
Feature Of Mechanical Fliter
●JTGMF Mechanical (Carbon,Sand)Filter Housing is an important part for Pure water preparation early pre-Finish and water purification system.It is apply to drinking water standard industrial water which is required filtered and general turbidity of treated water is within 5mg/L. It has good remove effect for suspended solids in industrial sewage.The Tablet agglomerated from suspended solids in water which can not remove through Precipitation method,we can through water to filter layer in filter vessel.Finally,to achieve transparency in water.
●JTGMF Mechanical Filter Housing using multichannel polishing processing to ensure the interface Ra reach to 0.6um close to sanitary level.All of the surface is mirror polished.
Application
●It is used in water Finish,mainly used in turbidity removal,reverse osmosis and The front-end preprocessing of lon exchange softening desalination system.It also can be used in remove sediment in Surface water and groundwater.The requirement of influent water turbidity should less than 20degrees,and the turbidity of treated water can below 3 degrees.
●Can be widely used in Electronic power,oil chemical industry,metallurgy,electroplating,paper making,textile,pharmaceutical dialysis,food and beverage,drinking water,Factories in water,swimming pool,etc.To meet the needs of the various industries liquid filtration.
The Characterstic Of Mechanical Fliter
●Barrels internal and external surface using mirror polish,interface Ra reach to 0.4um close to sanitary level.
●The equipment low cost,low Operating cost and easy management.
●Reasonable structure design,after Filter material backwashing can use many times,filter material has long service life,effective filtering and small occupation area.
Surface Finish
Finish Type | Mechanical polishing, electrolyticpolishing, sand blasting, pickling |
Polishing Precision | Inner surface Ra≤0.4μm , |
Operating Conditions
Max Operating Pressure | 0.4MPa, 0.6MPa |
Max Operating Temp. | 120℃ |
The filter shell adopts：ATM(pressure testwith full water) | |
Material
Filter shell | SS304, SS316L |
Stabilizer Blade, sling | SS304 |
Connect Pipe | SS304 |
O-ring | EPDM, PTFE, Viton, Silicone |
Connection
In-outlet N1, N2 | 1”/2”Flange, Tri-clamp,Thread |
Pressure gauge connectionN3, N4 | 1.5”Screw thread |
Vent valve connection N5 | 1/4”Screw thread |
Sight glass connection N6 | Flange |
Manhole N7 | Flange |
Packing Hand hole N8 | Flange |
Dimension Parameters | C： Shell diameter | ||||||||||
Φ600 | Φ800 | Φ1000 | Φ1200 | Φ1400 | Φ1600 | Φ1800 | Φ2000 | Φ2500 | Φ3000 | Φ3200 | |
A： Total height | 2350 | 2600 | 2800 | 2800 | 3000 | ||||||
B： The distance from inlet to center | 1500 | 1800 | 1800 | 2000 | |||||||
D： The height from packing hand hole to ground | 1200 | 1200 | 1200 | 1200 | |||||||
E: Equipment output(T/h) | 1.4～2.8 | 2.5～5.0 | 4.0～8.0 | 5.5～11 | 7.5.4～15 | 10～20 | 13～25 | 16～30 | 25～49 | 35～70 | 40～80 |
The above-mentioned data is the standard, it can customize according tocustomer's requirements.
Selection Table
Shell diameter | Shell material | In-outlet connection | O-ring | |||
600J | 4 | K | S | |||
600J=diameterΦ600 mechanical filtration | 4=304 | F=Flange | E=EPDM | |||
800J | 1000J | 1200J | 1400J | 6=316L | K=Tri-clamp | P=PTFE |
1600J | 1800J | 2000J | 2500J | L=Screwthread | V=Viton | |
3000J | 3200J | S=Silicone | ||||
